Home  > INFO CENTER  > News  >  FAQS On Optical Fiber Splicing Machine

FAQS On Optical Fiber Splicing Machine

2019-07-18


There will be some problems when we use the splicing machine. Don't panic. TUMTEC will answer your questions today.

First: Fusion splicing can not be normal splicing, splicing failure, red alarm

The cause of this failure may be the following:

1. Excessive splicing loss, or failure of fiber to fiber, or failure of fiber propulsion;

2. The end face of optical fiber is not smooth or has sundries;

3. There is something wrong with the optical system;

4.Splicing machine program problems;

Second:Splicing machine splicing loss is too large

The cause of this failure may be the following:

1. The end face of the optical fiber is not clean and has dust, or there are sundries on the v-groove, or there are sundries on the optical fiber fixing rack.

2. The cutting end Angle difference of optical fiber is too large;

3. There is something wrong with the optical system, and the objective lens leads to wrong estimation;

4. Splicing strength is not enough or too strong, discharge position deviation;

5. Splicing machine program error;

Thrid: Splicing machine tip can not find optical fiber

The cause of this failure may be the following:

1. There is something wrong with the optical system;



Four: Splicing machine hints to find the left fiber or can not find the right fiber

The cause of this failure may be the following:

1. The left optical fiber (right optical fiber) is not placed correctly, or there is sundry matter in the v-groove;

Motor propulsion system failure;

3. Faults of related components of the optical system, including objective lens, reflector and related control circuit;



Five: Splicing machine prompt discharge intensity is not enough

The cause of this failure may be the following:

1. The discharge intensity coefficient of the electrode is too low;

2. Too many times of electrode discharge, the surface has been cultured;

3. Unqualified electrode installation and poor contact;

 


Six:Optical fiber propulsion failure of splicingmachine

The cause of this failure may be the following:

(1) motor failure;

(2) the v-groove is blocked or unable to clamp the optical fiber;



Seven: Splicing machine tip left (right) fiber dirty or end face is not smooth, can not splice

The cause of this failure may be the following:

1. There are sundries in the relevant parts or uneven cutting of the end face of optical fiber;

2. Analysis of the impact of sundries on the lens mirror;



Eight:The display screen of splicing machine cannot display

The cause of this failure may be the following:

1. Whether the power supply and data cable of the display screen are connected normally;

2. When starting up whether you can see the motherboard information, if not may be the motherboard fault;

3. Boot can see the motherboard information, may be damaged screen, or optical system fault;



Nine:The splicing machine cannot be started

The cause of this failure may be the following:

1. Whether the meter power supply is normal;

2. Whether the switch of the meter is normal or not;

3.Boot can see the mainboard information, if not may be damaged mainboard;

4.If you can see the mainboard information before no reaction, or stuck, may be a program error or mainboard fault or screen damage;



Ten: Splicing machine button no response

The cause of this failure may be the following:

1.The relevant button failure;

2. Illegal operation;

3. Slow or crash;


Eleven:The splicing machine cannot heat the heat-shrinkable casing

The cause of this failure may be the following:

1. What is the temperature of the heater? Is there enough heat, such as enough heat to heat shrinkable casing;

2. If there is not enough heat, the heater may be damaged;

3. Check whether the power supply of heater is normal;



Twelve:Splicing machine power supply battery can not power

The cause of this failure may be the following:

1. The battery cell is damaged;

2. The battery charger is damaged or the charging circuit is damaged;

3. Poor charging connection;


Thirteen:Splicing machine cannot pass self-inspection

The cause of this failure may be the following:

1. If the parts fail to pass the self-inspection are damaged, they will be dealt with according to the corresponding faults;

2. Program error;

 


Tourteen:Splicing machine in the process of welding crash

The cause of this failure may be the following:

1. Program error;

2. Poor contact of key components of the instrument or unstable voltage;

3. Mainboard failure;


Chat Online 编辑模式下无法使用
Chat Online inputting...